A flickering light and a full rewire start the same way, with a call and a straight conversation about what is going on. Homestead Electrical Company handles the full range of residential and commercial electrical work in Homestead and across Miami-Dade County, from a dead outlet that needs a quick fix to a complete service upgrade on an older property. We work with homeowners, landlords, property managers, and businesses. The price is confirmed before anything is scheduled. Pricing set out up front. Code-compliant work. Reliable power. Give us a call and consider it handled.
Dealing with a tripping breaker or a dead outlet? Those symptoms point to something specific, and finding it is the first part of the job. A diagnostic visit covers the panel, the affected circuits, and the devices or fixtures that are behaving badly. We check for arc-fault and ground-fault conditions, test GFCI protection where it applies, and trace the fault back to its source before any work is priced or scheduled.
Common calls include flickering lights, outlets that stopped working, a burning smell near a switch or panel, sparks from a receptacle, and rooms or portions of the house with no power. Each one gets looked at with the same process: find the cause, explain what it is, and give you a plain answer on repair versus upgrade before anything is touched. One call gets the problem looked at properly.
Older panels and fuse boxes were not built to carry the loads a modern home or business puts on them. When a panel is undersized, outdated, or simply worn out, the right answer is usually a service upgrade rather than another patch. We handle 200-amp panel upgrades, fuse box replacements, service-entrance and meter upgrades, subpanel installation, and the load calculations that go with each job.
Panel capacity matters on the electrical supply side whenever a property adds a major appliance circuit, a new AC feed, a dryer, or a range. We run the dedicated circuit and confirm the panel can carry the added load. Wiring work is checked against code before sign-off, so the finished installation is ready for inspection. You get a straight answer about the work before it is scheduled, including what the upgrade involves and what it will cover once it is done.
Some homes need a full rewire. Others just need one outlet fixed. We handle both ends of that range and everything between. Outlet work includes standard receptacle replacement, GFCI outlet installation in kitchens, bathrooms, garages, and outdoor locations, AFCI protection where the code requires it, and USB outlet installation for convenience in bedrooms and offices. Switch upgrades cover dimmer installation, smart switch wiring, and three-way switch replacement.
Lighting covers recessed LED installation, under-cabinet lighting, exterior security lights, motion sensor fixtures, and landscape lighting runs. Rental properties and commercial spaces get the same attention as single-family homes. Outdoor lighting is grounded and bonded to meet code, and every installation is checked before we leave. Pick up the phone and we'll handle the wiring.
A ceiling fan installation is straightforward when an existing box is already rated for the load. When there is no box, or the existing one is not fan-rated, we swap it out and confirm the wiring is correct before the fan goes up. New installations that require a wiring run from the panel or a switch upgrade are handled the same way. We work in bedrooms, living rooms, covered patios, and porches, and we confirm the switch configuration matches what the fan needs before the job is called done.
You shouldn't have to chase an electrician for answers, especially when the job involves something as involved as a whole-home rewire or a new dedicated circuit for a major appliance. We install dedicated circuits for refrigerators, dryers, washers, ranges, hot tubs, and the electrical supply side of air-conditioning units. Each circuit is sized to the load and run to code.
Whole-home rewiring comes up most often in properties with knob-and-tube wiring, aluminum branch-circuit wiring, or wiring that has simply aged past the point of reliability. Aluminum wiring remediation is handled with the correct connectors and terminations at every device. Knob-and-tube replacement means pulling new copper branch circuits throughout and updating the panel to match. The work is scoped on the call so you know what it involves before anyone shows up.
A Level 2 EV charger runs on a dedicated 240-volt circuit, and installing one starts with a panel capacity check. If the panel has room, we run the circuit to the garage or parking location and install the outlet or hardwired connection the charger needs. If the panel is at capacity, we discuss the upgrade path before scheduling anything.
We protect your floors and finishes while we work, which matters in finished garages and living spaces where the wiring run passes through finished walls or ceilings. The circuit is sized to the charger's draw and confirmed before the job closes. Give us a call and consider it handled.
A flickering light and a full rewire start the same way, and so does electrical work for a renovation or a new build. The scope varies, but the process does not. We handle rough-in wiring for additions, kitchen and bathroom electrical work, garage circuits, shed wiring, and the full electrical scope on new construction. GFCI and AFCI protection is installed where the code requires it, and every circuit is mapped and labeled before the job is finished.
Landlords and property managers use us for rental property electrical work, pre-purchase inspections, and code violation repairs that come up after a failed inspection. Small businesses, retail spaces, and office buildouts are in scope as well. The job is scoped on the call, the price is confirmed before scheduling, and the work is done to the standard the Miami-Dade County inspectors enforce.
An electrical safety inspection covers the panel, the branch circuits, the grounding and bonding, and the devices and fixtures throughout the property. Common triggers include buying an older home, pulling a permit that requires sign-off, or dealing with wiring that has not been looked at in years.
We check for arc-fault and ground-fault protection where it is required, look for double-tapped breakers and undersized wiring, and flag anything that needs attention before it becomes a larger problem. If a property has failed an inspection, we identify the violations and carry out the repairs. The findings are explained clearly, and the repair path is laid out before any work is scheduled.
South Florida's storm season, year-round heat, and outdoor-living culture shape the electrical work that comes up most often here. Hurricane season runs June through November, lightning is a regular event, and backyard pools are a fixture of daily life in this part of Miami-Dade County. The three services below reflect that directly. This area has its own wiring habits. The work is matched to them. Everything is left to code.
A whole-home generator hookup means a transfer switch, a connection to the panel, and a load assessment to confirm the generator can carry the circuits you need running during an outage. When a storm knocks out power for days at a time, a properly wired standby generator is not a convenience. It is what keeps the refrigerator, the medical equipment, and the lights running. We handle the transfer switch installation, the dedicated circuit to the generator, and the panel connection, so the switchover is clean and the load is balanced.
Florida leads the country in lightning strikes, and Homestead sits in one of the most active corridors. A whole-home surge protector installed at the service entrance protects everything on the circuits from a voltage spike, whether it comes in from the utility line or from a nearby strike. Point-of-entry protection covers appliances, electronics, and the panel itself. We size and install the protection device, confirm the grounding is solid, and explain what the system covers before the job closes.
Pools are common here, and the electrical requirements for a pool or spa are specific. A dedicated circuit feeds the pump and equipment, GFCI protection is required at the outlets and fixtures around the water, and bonding connects the metallic components to prevent voltage differences in the water. We handle the full scope: the dedicated circuit, the GFCI protection, the bonding grid, and any exterior lighting around the pool area. The work is done to the code that applies to wet and outdoor locations in Florida.
Dealing with a tripping breaker or a dead outlet is stressful enough without having to guess what the repair will cost. When you call, we talk through what is going on, scope the job, and give you the rate before anything is scheduled. You get a straight answer about the scope and the price on the same call. There is no guessing, and there is nothing to figure out after the fact. That applies to straightforward repairs and to larger jobs like panel upgrades, rewires, and generator hookups alike. Ask what the job covers and you get a clear answer.
We work throughout Homestead and the surrounding communities in Miami-Dade County, including Florida City, Goulds, Leisure City, Naranja, Princeton, Cutler Bay, South Miami Heights, and Kendall. Residential work covers single-family homes, condos, and rental properties. Commercial work includes small businesses, office spaces, retail locations, and apartment buildings. Whatever the property type, the process is the same: scope the job on the call, confirm the price, and carry out the work to code. One call gets the problem looked at properly.
The panel inspection covers breaker condition, correct sizing for the circuits they protect, signs of overheating or corrosion, double-tapped breakers, and whether the grounding and bonding are in order. In older homes, we also check whether the panel type and capacity are appropriate for the current load. Any findings are explained before repair or upgrade work is quoted.
The visit starts with confirming the scope from the call, then moves to a hands-on look at the panel, the affected circuits, and the devices or fixtures involved. Fault-finding comes before repair, so the cause is identified before any work is priced or started. Once the work is done, the circuit is tested and confirmed before we leave.
A whole-home surge protector installs at the service entrance and intercepts voltage spikes before they reach the branch circuits. Florida sees some of the highest lightning strike rates in the country, and a single surge can damage appliances, electronics, and wiring in ways that are not always obvious right away. The device is sized to the service and paired with solid grounding to be effective.
We are available every day from 9:00 AM to 11:00 PM, and emergency calls during those hours are taken seriously.
Call (786) 926-3289 and describe what is happening.
We will talk through the situation on the call and confirm what the schedule allows for a short-notice visit.
Do not reset a breaker that keeps tripping on its own, and do not use an outlet or circuit that is sparking, buzzing, or producing heat. If the panel itself is the problem, leave it alone. Turn off the affected circuit from the panel if it is safe to do so, and keep people away from the area until we arrive.
It starts with the call, where the current panel, the property's wiring type, and the scope of the work are discussed. A load calculation is part of scoping a panel upgrade correctly, and a rewire scope depends on what type of wiring is in the walls and how accessible they are. The price is confirmed before anything is scheduled, and permit requirements are handled as part of the job.
Common triggers include buying an older home, scheduling a renovation that will affect the electrical system, dealing with a failed inspection, or simply not knowing when the wiring was last looked at. Post-storm assessments are also a reason to schedule one in South Florida, where a nearby lightning strike or surge can affect wiring and devices without an obvious outward sign.
Wiring that runs through finished walls, crawl spaces, or attics takes more time to access and trace than wiring in open framing. Older wiring types such as knob-and-tube or aluminum branch-circuit wiring also require specific handling and materials that differ from a standard repair. The call is where we talk through what the property has and what that means for the scope and price.
Yes. For work that requires a permit under the applicable code, we handle the permit side as part of the job. That includes panel upgrades, rewires, new circuit runs, and other work that triggers a permit requirement in Miami-Dade County. Permit fees and what they cover are explained on the call when the job is scoped.
Outdoor wiring is installed in weatherproof conduit or rated enclosures appropriate for Florida's climate, and every exterior outlet and fixture is GFCI protected where the code requires it. Bonding for pool and spa equipment is handled as part of the outdoor electrical scope when it applies. The grounding is confirmed before the work is closed out.
A repair addresses a specific fault: a bad outlet, a failed GFCI, a tripped breaker with an identifiable cause. A rewire replaces the branch-circuit wiring itself, either in part or throughout the home, and is the right answer when the wiring type or condition is the underlying problem rather than a single device. The inspection on the call or on-site determines which one applies.
Homestead Electrical Company is available every day from 9:00 AM to 11:00 PM.
Whether the job is a single outlet repair or a full panel upgrade, the first step is the same: call (786) 926-3289, describe what is going on, and get a price before anything is scheduled. Pricing set out up front. Code-compliant work. Reliable power.
Every electrical job starts the same way: a call, a clear conversation about what is going on, and a price confirmed before anything is scheduled. The table below covers the full range of work we handle in Homestead and across Miami-Dade County. Use it to find the service that fits your situation, then call us and we will scope the job from there.
| Electrical Service | What It Covers | Ideal For | What to Keep in Mind |
|---|---|---|---|
| Electrical Repairs & Troubleshooting | Fault tracing and diagnostics, GFCI and AFCI testing, Dead outlets and flickering lights, Burning smells and sparks | Any home or business with a symptom that needs a cause identified before repair work begins | Finding the fault first keeps the repair scoped correctly. We explain what we find before any work is priced. |
| Electrical Panel & Service Upgrades | 200-amp panel upgrades, Fuse box replacement, Service entrance and meter work, Subpanel installation | Older homes adding major appliances, AC feeds, or EV chargers that the existing panel cannot support | A load calculation is part of every panel upgrade so the new service is sized to what the property actually needs. |
| Whole-Home Generator Installation | Transfer switch installation, Panel connection and load assessment, Dedicated generator circuit, Switchover confirmation | Homestead properties that need reliable power through hurricane season and extended outages | A proper transfer switch keeps the generator load balanced and prevents back-feed onto the utility line. We scope the circuit and panel connection on the call. |
| Ceiling Fan Installation | Fan-rated box installation, Wiring runs from panel, Switch configuration, Covered patio and porch installs | Bedrooms, living rooms, and outdoor living spaces where no fan-rated box currently exists | If the existing box is not fan-rated, we swap it before the fan goes up. The switch configuration is confirmed before the job closes. |
| Breaker & Fuse Repair | Breaker testing and replacement, Fuse box assessment, Tripping breaker diagnosis, Double-tapped breaker and overload correction | Properties with breakers that trip repeatedly or a fuse box that can no longer handle the load | A breaker that trips on its own is pointing to something. We trace the cause before swapping hardware. |
| Pool & Spa Wiring | Dedicated pump circuit, GFCI protection at pool outlets and fixtures, Bonding grid installation, Exterior pool area lighting | Homestead homes adding or updating a pool or spa where code-compliant wiring and bonding are required | Bonding connects metallic pool components to prevent voltage differences in the water. We handle the full electrical scope, not just the outlet. |
| Surge & Lightning Protection | Whole-home surge protector at service entrance, Point-of-entry voltage spike protection, Grounding confirmation, Appliance and electronics coverage | Any Homestead property in a high-lightning corridor where a single surge can damage wiring and appliances | Florida sees some of the highest lightning strike rates in the country. A service-entrance device intercepts spikes before they reach the branch circuits. |
| Lighting Installation | Recessed LED installation, Exterior and security lighting, Motion sensor fixtures, Landscape lighting runs | Homeowners and landlords updating interior lighting or adding outdoor coverage around the property | Outdoor fixtures in South Florida need to be rated for the humidity and heat. Every exterior installation is grounded and bonded to code. |
| Electrical Safety Inspections | Panel and breaker review, Grounding and bonding check, Arc-fault and ground-fault assessment, Code violation identification | Buyers of older homes, landlords after a failed inspection, and properties that have not been looked at in years | Post-storm inspections are worth scheduling in South Florida, where a nearby lightning strike can affect wiring without an obvious outward sign. |
| Outlet & Switch Installation | GFCI outlet installation, AFCI protection, Dimmer and smart switch wiring, USB outlet installation | Kitchens, bathrooms, garages, outdoor locations, and any room needing updated receptacles or switch configurations | Code requires GFCI protection in wet and outdoor locations. We confirm what applies before the work is scoped. |
| Wiring & Circuit Installation | Whole-home rewiring, Knob-and-tube replacement, Aluminum wiring remediation, New branch circuit runs | Older properties with outdated wiring types or homes being renovated where the existing wiring cannot support the updated load | Aluminum branch-circuit wiring requires specific connectors and terminations at every device. The scope is discussed on the call before anyone shows up. |
| Dedicated Appliance Circuits | Dryer and range circuits, Refrigerator and washer circuits, AC supply-side circuit, Workshop and garage circuits | Any major appliance or equipment that needs its own circuit sized to the load | We handle the electrical supply side for AC units: the dedicated circuit, the disconnect, and the panel capacity check. The unit itself is outside our scope. |
What are the signs that a breaker panel needs to be upgraded rather than repaired?
A panel that is consistently overloaded, runs hot, shows signs of corrosion or scorching, or simply cannot carry the circuits a modern property needs is a candidate for replacement rather than a patch. Fuse boxes and older panel types that are no longer code-compliant also fall into this category. When you call, we talk through what the panel is doing and whether an upgrade is the right answer before anything is scheduled.
What causes a breaker to trip repeatedly on the same circuit?
Repeated tripping usually points to one of three things: the circuit is overloaded by the devices on it, there is a wiring fault somewhere along the run, or the breaker itself has failed and is no longer holding correctly. A diagnostic visit traces the cause before any replacement work is priced. Swapping the breaker without finding the underlying reason often means the problem comes back.
What does aluminum wiring in an older home mean for safety and repairs?
Aluminum branch-circuit wiring was common in homes built during certain decades and is still present in many properties in this area. It is not automatically a crisis, but it does require specific connectors and terminations at every outlet, switch, and fixture to handle correctly. Standard copper connectors are not the right fit. When we scope a job in a home with aluminum wiring, we confirm what the wiring type means for the repair or upgrade before any work begins.
Faults Traced Before Anything Is Replaced
We find the cause of the problem before recommending a repair. That keeps the scope accurate and keeps you from paying for parts that were never the issue.
How do I know if my home is ready for the electrical load of an EV charger?
A Level 2 EV charger runs on a dedicated 240-volt circuit, and whether your panel can support one depends on what load it is already carrying. We start with a panel capacity check on the call and confirm whether there is room before scheduling the circuit run. If the panel is at capacity, we walk through the upgrade path so you know what is involved and what it costs before anything is committed.
What is involved in wiring a backup generator for a home in South Florida?
A whole-home generator hookup covers the transfer switch, the dedicated circuit from the panel to the generator, and a load assessment to confirm the generator can carry the circuits you need during an outage. The transfer switch is what keeps the generator from back-feeding onto the utility line and keeps the load balanced. We scope the panel connection and circuit on the call so the work is fully understood before it starts.
Why do outlets and switches sometimes stop working even when the breaker has not tripped?
A GFCI outlet that has tripped upstream can cut power to a whole run of outlets without the main breaker moving. A loose connection at the device or in the junction box can do the same. Worn receptacles that no longer make solid contact are another common cause. The diagnostic covers the panel, the GFCI protection on the circuit, and the device itself so the actual cause is found rather than guessed at.
Permits and Inspections Handled Where Required
For panel upgrades, rewires, and other work that triggers a permit requirement in Miami-Dade County, we handle the permit side as part of the job. What it covers is explained on the call.
What do flickering or dimming lights usually mean?
Occasional flickering tied to a large appliance starting up is normal. Persistent flickering, dimming that happens without an obvious trigger, or lights that flicker in multiple rooms at once points to something that needs a closer look. Loose connections, an overloaded circuit, a failing breaker, or a problem at the service entrance can all show up this way. We check the panel and the affected circuits to find the source.
Is a warm or buzzing outlet a problem that needs immediate attention?
Yes. An outlet that is warm to the touch, buzzing, or producing a burning smell is not something to leave for later. Those are signs of a wiring fault, a loose connection, or a device that is drawing more current than the circuit can handle safely. Turn off the circuit from the panel if it is safe to do so and call us. We are available every day from 9:00 AM to 11:00 PM.
Code-Compliant Work on Every Job
Wiring work is checked against code before sign-off. The finished installation is ready for inspection, and the findings are explained clearly before we leave the property.
How does GFCI protection work and where is it required?
A GFCI outlet monitors the current flowing through a circuit and trips instantly when it detects a difference between the hot and neutral that could indicate a shock path. Code requires GFCI protection in kitchens, bathrooms, garages, outdoor locations, and anywhere near water, including pool and spa areas. We confirm what applies to your property before the work is scoped, and we test every GFCI installation before the job closes.
How long does a panel upgrade typically take?
Most panel upgrades are completed in a single day. The exact time depends on whether the service entrance also needs work, whether a subpanel is part of the scope, and how the existing wiring is configured. We talk through the scope on the call so you have a realistic picture of what the day involves before anything is scheduled. Permit requirements for panel work in Miami-Dade County are handled as part of the job.
What does it mean to add a circuit for a workshop or large appliance?
A dedicated circuit is a run from the panel sized specifically for one load, whether that is a table saw, a dryer, a welder, or a refrigerator. It means that appliance is not sharing capacity with anything else on the circuit, which protects both the equipment and the wiring. We size the circuit to the load, confirm the panel has capacity, and run the wire to the location the appliance needs.
Call (786) 926-3289 and tell us what is going on. We will scope the job, confirm the price, and get it on the schedule.
(786) 926-3289